Small flour machinery common problems and solutions

Small flour machinery common problems and solutions
Due to its use characteristics, small flour machinery usually works for a long time without interruption. However, due to the lack of proper use of specifications, there are some common problems. If not solved in time, it will seriously affect the service life of small flour machinery and cause funds. The waste, the following Hualiang Flour Machinery Xiaobian will introduce the common problems of small flour machinery and solutions.
1. Is the pipeline smooth?
Due to the high temperature and humidity in summer, the inner wall of the slide tube made of metal is easy to condense, so that the flour adheres to the inner wall of the slide tube, which causes the smoothness of the inner wall of the slide tube to drop, causing blockage of the pipeline, which can seriously damage the equipment or cause a complete machine accident. ;
Corresponding solution: When the pipeline is clogged, the inspection hole can be opened first to let the material discharge to the ground to prevent blockage to the equipment, resulting in equipment damage.
2. Is the high square screen sifted?
Gao Fangping sieve sieve is because the humidity is high in summer, the humidity in the sieve bin is also high, the flour is easy to get wet during the sifting process, the moisture is not easily taken away by the airflow, and the internal temperature of the sieve bin is easy to be formed because of the high temperature and high humidity. When the flour passes through the sieve hole of the sieve, it is easy to stick to the sieve mesh, block the sieve hole, reduce the sieve area, push the material back, the good powder output rate decreases, and the total flour extraction rate of the flour is also affected. .
Corresponding solution: The solution that can be used for high-screen sieve paste screen is to properly sift the size of the flour sieve. Generally, the flour screen can be diluted one model in the summer, and the original sieve will be restored after the summer. .
3. Does the mill have a roll phenomenon?
The flour mill is wrapped around the roller because the material contained in the mill is excessively powdery and the humidity of the flour is large and the rolling distance is too tight;
Corresponding solution: the roller phenomenon of the grinding machine can be strengthened by adjusting the grinding roller cleaning device, but the rolling distance is not easy to be too tight, and it is appropriate; in addition, the rolling distance of the winding roller mill can be appropriately relaxed in summer, and the machine is checked. Whether the material contains powder, if there is too much powder, adjust the screen to reduce the amount of powder.
4. Does the resistance of the high-pressure wind network pulse exceed the standard?
By the same token, the resistance of the pulse dust collector of the high-pressure wind network rises because of the high temperature and high humidity in summer, and the humidity of the air in the pneumatic conveying is large. When the drum is filtered by the pulse dust collector, the cloth will be wet, and the dust will stick to the cloth. The surface, blocking the pores of the cloth.
Corresponding solution: The resistance of the pulse dust collector can be increased by increasing the air volume of the reverse blower and the blowing frequency of the reverse blower. If necessary, the time interval for replacing the cleaning cloth can be shortened, and the cloth can be replaced in time.
Finally, after the end of the small flour machinery work, it is necessary to carry out certain cleaning, to clean up some impurities generated during the work, and to prevent blockage when the next use.

Long Range LiDAR Radar

Long distance LiDAR sensor series are particularly easy to communication thanks to their fixed connector, which can be plugged it up and off by yourself. Voltage is wider from 8v before to 36v. Low power consumption feature makes it beceome a very competitive, high performance-price ratio, long range Laser Distance Sensor.

Highlights:

> Measurement frequency: 400 Hz (Max 60m 3000Hz)
> Long range: 200m
> High temperatures: -10~+50℃
> UART output
> Connector design: easy to use


Parameters:

Accuracy

±10cm(<50m) /±1%(>50m)*

Measuring Unit

cm

Measuring Range (without Reflection)

0.1-200m

Interface options

Serial/usb/rs232/rs485/bluetooth

Measuring Frequency

400 Hz

Laser Class

Class I

Laser Type

905nm

Weight

About 20g

VInput Voltage

8V-36V

Resolution

1cm

Size

43*35*21mm

Operating Temperature

-15℃~50℃

Storage Temperature

-40℃~85℃


Chengdu JRT Main Ranging Modules: Industrial Laser Distance Sensors, Laser Rangefinder Sensor, Tof LiDAR Sensors.

Speed Laser Sensor,Long Range Lidar,Long Range 3D Lidar,Long Range Radar Sensor

Chengdu JRT Meter Technology Co., Ltd , https://www.irdistancesensor.com